1.柔性填料产品特点：柔性填料具有优良的性、高塑性、耐热性、耐寒性、耐老化性，还具有操作简便，无毒无味，耐水、粘附性能好等特点，且施工投入的人员相对较少，便于加工成型，施工工艺简单，造价低廉。柔性填料的特点是具有优异的变形性和流动性，在水压力作用下可以流动，挤入缝中起到止水作用，抗渗性能优异，能对孔隙、缝隙起到封闭止水作用。GB柔性填料还具有良好的黏接性能，与混凝土的黏接强度大于材料自身的拉伸强度，可确保在各种工况下黏接界面不发生破坏。同时，GB柔性填料还具有优良的耐介质性，即耐水、耐碱盐浸泡，对环境具有很强的适用性，耐冻融循环，并具有一定的耐寒性和耐高温性。GB柔性填料可根据需要加工成各种形状及断面尺寸的型材，便于施工。
1. product features: flexible flexible filler filler has excellent plasticity, unique, high heat resistance, cold resistance, aging resistance, but also has the advantages of simple operation, non-toxic and tasteless, the characteristics of water resistance, good adhesion, and the construction investment staff is relatively small, easy processing, simple construction process, low cost. The most important feature of flexible packing is excellent deformation and fluidity. Under the action of water pressure, it can flow and squeeze into the joint to play a role of water stopping. It has excellent impermeability and can seal water and pore. GB flexible packing also has good adhesion performance. The bonding strength to concrete is greater than the tensile strength of the material itself, which ensures that there is no damage to the bonding interface under various working conditions. Meanwhile, GB flexible packing also has excellent dielectric resistance, that is, water and alkali resistant salt immersion. It has strong applicability to environment, freeze-thaw cycle, and has certain cold resistance and high temperature resistance. GB flexible packing can be processed into various shapes and section sizes according to the needs, which is convenient for construction.
2.柔性填料应用范围：
2. application scope of flexible packing:
（1）各种大中型水电工程大坝的伸缩缝及周边缝。
1 expansion joints and peripheral joints of various large and medium-sized hyower projects.
（2）大型层面板、伸缩缝、女儿墙与屋面接缝的防漏。
2 a large leak layer panel, expansion joints, and the joints of roof parapet.
（3）大型层面板、伸缩缝、活动房屋、卫生间的防水密封。
3 waterproofing and sealing of large floor panel, expansion joint, movable house and toilet.
（4）地下室、人防工程、遂道地铁、涵洞以及各种给排水工程的止水密封。
4 the basement, the air defense project, subway, tunnels and tunnel drainage engineering to various water seal.
（5）混凝土与橡胶、塑料、陶瓷及各种金属材料的粘结密封。
5 the bonding and sealing of concrete to rubber, plastics, ceramics and all kinds of metal materials.
3.柔性填料施工方法：
3. construction method of flexible packing:
柔性填料系填在周边缝顶部预留“倒△”形槽内，必须粘紧密实，并呈弧形向上隆起，以便能更好地适应面板变形，在其表面采用聚氯乙烯塑料带包盖密封死水位以上采用钢片，要用角钢通过螺栓将其嵌固在砼上。
Flexible filler to fill in the top line of peripheral joint reserved inverted triangular groove, you must stick with dense, and curved upward, in order to better adapt to the deformation of the panel, on the surface of the PVC plastic tape sealing cover dead water level above the steel plate, to use the embedded angle through bolts solid in concrete.
柔性填料施工前应先将其与砼结合部位用钢丝刷刷去砼表面的乳皮，然后用高压水枪冲洗干净，风干后再用，
The construction of flexible packing should be preceded with the concrete binding site to use wire brush on the surface of concrete milk skin, and then rinse with water cannons, dry and then,
1施工准备用钢筋台车将GB柔性填料、GB防渗盖板、电镀角钢及电镀膨胀螺栓等运至相应的施工部位。
1 the construction is ready to use the GB flexible packing, GB anti seepage cover plate, electroplating angle steel and electroplating expansion bolt to the corresponding construction site.
2嵌缝处理用钢刷将预留“v”槽内两侧清理干净，再用水冲洗槽内外，除去缝面上的灰砂。“V”槽清理干净后自然晾干。
2 the steel brush will be reserved for the "V" slot on both sides of clean caulking treatment, then rinse tank inside and outside, remove seam on the surface of the sand. The "V" trough is cleaned and dried naturally.
3）GB柔性填料填缝用黏合剂将槽内、外壁均匀涂刷一遍，外壁要相应涂刷的宽一些，不可漏刷。黏合剂刷好晾1h后，手感快干时，先在槽底沿槽走向放置一条PVC棒。再将GB柔性填料均匀切成条状压入槽内，并在外壁按设计要求的弧状堆起2cm高。用手捶捶紧，嵌填一定要密实。GB柔性填料嵌填完毕后，要及时盖上防渗盖板，再用冲击钻钻孔，安装电镀角钢后埋设10 x75电镀膨胀螺栓，间距为400mm。利用电镀角钢通过电镀膨胀螺栓将GB防渗盖片嵌固在砼上。
3 the GB flexible filler filler used the adhesive to paint the inner and outer walls evenly, and the outer wall should be brushed in a wider range and not to be leaked. When the adhesive is brushed to dry the 1H, when the f
